Schedule Now!

 

 

How do you feel with regards to A Step-by-Step Guide to Installing a Bathtub?

Installing a tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the project can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the brand-new one. Make sure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is better to take into consideration using one before you start. Opportunities are you might require a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have already purchased a new tub as well as don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Getting ready for the Installation

Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final placement.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the staying water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the level reads level.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the bath tub and additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washers remain in area in between the tap as well as the sink. Protect the tap in place with the manufacturer provided backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind should be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious reader on How to Install a Bathtub, I was thinking sharing that article post was a good thing. Appreciated our article? Please share it. Help another person check it out. Thanks so much for going through it.

Contact Us Now